How To Repair Faucets In The Bathtub
Do you wanna learn how to supplant a bath faucet?
Perhaps the prior homeowner had bad gustation?
Or the electric current faucet only isn't your style?
You tin can easily practise this project But you'll need the correct tools and tips.
Hey, that'south where I come in!!
I'll show you iii tools that brand swapping out faucets easy.
I'm going to giveaway my favorite ane, so don't miss out 😀
Several years agone I tried to remove a faucet in a rental I was rehabbing.
Go along in mind I was a beginner DIYer.
After 3 hours of claret, sweat and a few curse words that began with "S" I finally got the faucet off the sink.
Information technology should have taken me 10 minutes.
What a WASTE of time.
I don't want you lot to experience the same mistakes.
You'll take a much happier experience after reading and watching my secret tips.
Hither'south the supply list for today's bathroom faucet project
- Basin Wrench ($xvi) or
- Ridgid Faucet and Sink Installer Tool ($20)
- Crescent Wrench Set ($19 or FREE)
- Channel Locks ($12 or Free)
- WD-40 ($four)
- New Faucet ($50-$300)
- Plumber's Putty ($four)
- Plastic Container for P-Trap (Gratis)
- Towels or Rags (FREE)
- Sponge with Scrubbing Pad ($1)
- Measuring Tape (Complimentary or Borrow)
Permit'due south dive into this tutorial 😀
How to remove a bath faucet without blasphemous
I've had my share of curse words.
Peculiarly when doing plumbing, but you lot tin easily avoid this favorite American pastime.
The first step is to turn the shutoff valves to the off position by turning them clockwise until they stop.
This stops the flow of h2o to your faucet.
If for some reason your shutoff valves don't piece of work you'll have to turn the h2o off at the main water valve.
Water principal valves are typically in a basement or utility room.
Place your plastic container under the P-Trap.
Then unscrew the slip nuts holding the P-Trap to the drain and pipe coming from your wall.
Turn the skid nuts counterclockwise by hand or with channel locks.
As you loosen the slip nut that connects the P-Trap to the goose neck coming from the wall you lot'll run into water period from the pipes.
THIS IS NORMAL.
The h2o in the P-Trap prevents sewer gas from entering your bathroom through your sink.
As a side notation, if you bathroom does have that sewer odor it'due south probably due to
- A dry out sink P-Trap
- A dry out shower or tub P-Trap
- Your toilet needing a new wax ring
Water can be good or bad.
When it comes to preventing sewer gas, water is your best friend!
TOOL Time.
Grab either a bowl wrench or Ridgid Faucet & Sink Installer tool.
Reach up under the sink, attach the basin or Ridgid tool on the supply line nuts, and turn the tool clockwise.
Do this for both the hot and cold water supply lines.
This volition loosen the nuts and allow you to remove the supply lines from the faucet.
Use the aforementioned tool to loosen the plastic nuts that concur the faucet to the sink.
Plus, if y'all accept problem you lot tin can spray these nuts with WD-40 and come back in 15 minutes to endeavor the process over once again.
Information technology's Astonishing what WD-40 can do to loosen stuck objects.
One time the faucet nuts are removed you tin can pull the old faucet upwards from the sink.
Using these tools will totally relieve your a TON of time and preclude bloody knuckles.
It's (in my humble opinion) near incommunicable to utilize a standard wrench to remove a bathroom faucet.
A basin wrench or Ridgid Faucet & Sink Installer tool are Crawly.
The next pace is to have out the old drain.
Scary?
Not at all.
Remove the clip holding the pivot rod to the clevis strap.
Slide the clevis strap off the pivot rod then plough the bleed clockwise with channel locks.
Don't worry, I evidence you lot how to practise all of this in the video tutorial 😀
You'll so be able to pull the top of the bleed out from the sink.
Your drain will likely be disgusting.
Clean it thoroughly with rags and water or in my case I used Clorox wipes.
As well clean off the area where the onetime faucet used to be.
Now you're ready for the replace the old faucet with a vivid and shiny new ane!
Installing your new bathroom faucet: steal these tips to make your life easier
First things commencement.
Make sure you have the correct size faucet.
Measure the distance between the holes in the sink.
If yous only accept one hole then your life is easy already, haha.
In this example the holes are four inches apart.
Buy a new faucet that fits this dimension.
What brand of faucet should you lot consider?
Hither are my recommendations
- Delta
- Moen
- Kohler
- American Standard
Why?
They work, are simple to install, and give you replacement parts for Costless.
I particularly like the gratuitous replacement parts.
Let me share why I actually dearest Delta.
They replaced our oil rubbed bronze faucet handles for free.
The handles were chipping at the bottom due to hard water deposits.
Each handle would accept been $fifty but Delta sent them at no cost.
NICE!!
Check out my video to see the complete stride-by-step of how to supplant a bathroom faucet.
The first 5 minutes shows you how to remove your old faucet and at the 5:xxx mark I begin the faucet installation procedure.
This calendar week's video is a bit long simply I wanted to make certain you lot got a super thorough explanation.
What'due south Next
If you desire to make swapping out h2o supply lines easy then check out Fluidmaster'southward Click Seal connectors, they're awesome.
If you lot're doing a bathroom remodel and need assistance, join one of our online courses – they'll make your bath renovation much easier!
Let me know if you have any questions and I'll exercise my all-time to assist.
Thanks as ever for reading, watching, and existence function of our awesome community.
Cheers,
Jeff
Replace a Bath Faucet
Source: https://homerepairtutor.com/how-to-replace-a-bathroom-faucet/
Posted by: morsegratch.blogspot.com
0 Response to "How To Repair Faucets In The Bathtub"
Post a Comment